Skip to main content
Download PDF

Construction of a novel digital method for quantitative analysis of occlusal contact and force

BMC Oral Health volume 23, Article number: 190 (2023) Cite this article

Abstract

Background

Occlusal analysis is essential in the dental clinical practice. However, the traditional occlusal analysis performed on the two-dimensional level can not directly correspond to the tooth surface with three-dimensional profile, therefore the clinical guidance value is limited.

Methods

By combining the 3D digital dental models and quantitative data from 2D occlusal contact analysis, this study constructed a novel digital occlusal analysis method. The validity and reliability of DP and SA were verified by comparing the results of occlusal analysis of 22 participants. ICC values for occlusal contact area (OCA) and occlusal contact number (OCN) were tested.

Results

Results confirmed the reliability of the two occlusal analysis methods with ICC values of 0.909 for SAOCA, 0.906 for DPOCA, 0.929 for SAOCN and 0.904 for DPOCN. The Bland-Altman plot, paired t-test (tOCN = 0.691, P > 0.05) and Pearson correlation analysis results (R = 0.68, p < 0.001) verified the validity between SA and DP. Then a novel digital occlusal analysis method was constructed, which not only can locate the occlusion contact and provide the quantitative analysis, but also provide a comprehensive description of the resultant force of each tooth and the component forces on the x-, y- and z-axis.

Conclusions

This new occlusal analysis method can obtain quantitative analysis of occlusal contact including contact area and force information simultaneously, which will provide new impetus and greater help for clinical dental treatment and scientific research.

Peer Review reports

Background

Occlusion is closely related to oral health and considered as an important indicator of the functional status of the masticatory system [1, 2]. Occlusal analysis plays an important role in the diagnosis, treatment and prognosis evaluation in the field of prosthodontics [3, 4], orthodontics [5,6,7], implants [8], maxillofacial surgery [9], etc.

Every improvement in occlusal analysis methods has brought great changes to dental practice. Generally, the content of occlusion analysis should include occlusal contact area (OCA), occlusal contact number (OCN) and occlusal force. The articulating paper has always been a traditional tool for occlusal analysis, and is widely used in clinical practice because of its simplicity and intuitiveness. However, the size and distribution of occlusal contact can only be determined according to the doctor's experience [10]. It can not be used for quantitative analysis.

In recent years, the advent of occlusal analysis systems such as the T-scan system [11], Dental Prescale system [12], Blue Silicone system [13], etc. makes quantitative measurement possible. These systems use a media, such as silicone, PTE film or piezoelectric transducers, to analyze occlusal contact. For example, Dental Prescale occlusion analysis system uses a pressure-sensitive film with polyethylene terephthalate (PET) shells, which contains a pigment layer which consists of small dye capsules and a colour development reagent layer. When pressure is applied to film, the dye capsule ruptures and releases the colourless dye to mix with the substance in the colour development layer, thus presenting colour changes at where under the pressure [14]. The colour changes can be interpreted in the software to calculate the occlusal force value of each occlusal contact point. It can obtain the OCA values and absolute values of occlusal forces [15,16,17]. However, the data obtained on the two-dimensional level of these systems can not directly correspond to the tooth surface with three-dimensional profile, therefore the clinical guidance value is limited.

The rise of digital technology has brought new ideas to the development of dental analysis instruments [18,19,20,21,22]. The intra-oral scanners allow dentists to obtain three-dimensions digital models of the dentition directly [23, 24], with the advantages of high accuracy, enhanced patients’ comfort and possibility of quantitative analysis [25, 26]. As an important part of digital workflow, digital analysis software provides powerful function for the measurement of distances, areas, coordinates, errors, etc. [27, 28]. In recent years, the integration of digital technology into occlusal analysis has led to the development of occlusal analysis methods based on 3D dental models [29]. The advent of these methods has made it easier to quantify OCA, etc., however, the analysis of bite force is still lacking.

A combination of the 3D dental models obtained by intraoral scanning and quantitative data from 2D occlusal contact analysis, make it possible for quantitative analysis of occlusal contact and force simultaneously. This study constructed a novel digital occlusal analysis method which can not only be used to locate the occlusal contact on the tooth surface, but also to make quantitative analysis of OCA, OCN and occlusal contact force of each teeth, or part of dentition.

This study consists of two parts. Firstly, the consistency of used 2D and 3D methods was evaluated in vivo. After confirming the consistency, these two methods were used to construct a novel occlusal analysis system.

Materials and methods

Evaluation of the consistency of used 2D and 3D methods

Subjects

The evaluation trial enrolled twenty-two subjects (mean age 23.1 ± 3.2 years), all of whom were dental students at the first author's institution. All participants had complete dentition; no temporomandibular joint disease; no periodontal disease; and no orthodontic treatment. Ethical approval was granted by the Ethical Committee of the first author’s university (approval number: IRB-REV-2021143). All subjects gave informed consent before participating in the study.

Dental prescale analysis system (DP)

Before measurement, subject was asked to practice biting to find their intercuspal position (ICP). The pressure-sensitive films (Dental Prescale II, GC, Japan) are available in three sizes, S/ M/ L, and the appropriate size was selected according to the size of the subject's dental arch. The film was placed on the subject's mandibular arch, ensuring that it covered the entire dentition. The subject was then asked to bite with the maximum force into the ICP position and held for more than 3 s. After removing the saliva and drying, the film was immediately transferred to the scanning instrument (Perfection V600 Photo Scanner, Epson, Nagano, Japan) and the data were analyzed with the specific software (GC Bite Force Analyzer software, GC Corp.) to obtain a 2D occlusal contact graph, from which the OCA, OCN and occlusal force can be obtained (Fig. 1).

Fig. 1
figure 1

Occlusion analysis using the DP system. a. The pressure-sensitive film used in the DP system. b. Remove stray points that are significantly off the dental arch. c. 2D occlusal force analysis graph obtained from DP. d-e. Select the occlusal contact point. f. Measure the occlusal contact area and occlusal contact force

Full size image

Scanning of articulating paper marks (SA)

Arch-shaped articulating paper (BK52, Bausch Germany GmbH, Hainspitz, Thüringen, Germany) was placed on the occlusal surface of the mandibular dentition. After ensuring that the articulating paper covered the entire dentition, the subject was instructed to bite with the maximum force into the ICP. After removing the articulating paper, the maxillary and mandibular dentition were scanned immediately using an intraoral scanner (Trios 3 Shape; 3Shape A/S, Copenhagen, Denmark) to obtain a 3D model with the colored marks of the articulating paper. The data were saved in "ply." Format and imported into a 3D data processing software (Geomagic Wrap 2017; 3D Systems, Rock Hill, SC, USA) where the teeth with occlusal marks could be observed. Each occlusal contact was outlined according to the color difference. The OCA and OCN values were obtained using the software's area measurement function (Fig. 2).

Fig. 2
figure 2

Occlusion analysis using the SA system. a. Digital model obtained by scanning. b. Outline the occlusal contact points. c. 3D occlusal analysis graph obtained from SA

Full size image

Reliability testing

For each method, a test–retest check was performed for all subjects two weeks after the initial test. All operations were performed by the same operator. Intraclass correlation coefficient (ICC) was used to evaluate the test–retest reliability for both systems with high ICC values representing high reliability.

Validity testing

Validity between the two systems was evaluated by comparing the OCA and the OCN obtained from DP and SA. The Shapiro–Wilk test was used to confirm the normality of the data sets. And then Paired t-tests were used to evaluate whether there was a significant difference in OCA and OCN obtained from DP and SA. Pearson correlation analysis was used to analyze the correlation between the OCA obtained from DP and SA. In addition, linear regression was used to evaluate the linear relationship between the data obtained from DP and SA.

Statistical analysis was performed using the SPSS v23 (SPSS Inc., Chicago, IL, USA), and GraphPad v8.0.2 (GraphPad Prism Software Inc., San Diego, CA, USA). For all analyses, statistical significance was preset at α = 0.05.

Construction of the 3D occlusal force analysis system

Overlapping DP and SA records

First, the 3D dental model with occlusal markers was rotated in Geomagic Wrap and its mandibular occlusal plane was adjusted to be parallel to the screen. Then, a screenshot was taken to obtain a 2D view of the occlusal plane of the 3D dental model. The 2D occlusal force analysis graph from Dental Prescale system and the screenshot of the occlusal surface of the 3D dental model were overlaid and the occlusal contact points measured by the two analysis systems were matched. The area of each occlusal contact point and the values of the occlusal forces were recorded (Fig. 3).

Fig. 3
figure 3

Overlapping DP and SA records

Full size image

Construct a 3D occlusal force analysis model

Then, a 3D coordinate system was constructed in Geomagic Wrap software. The midpoint between the mesial line angles of the mandibular central incisors was taken as the origin. The x–y plane coincided with the mandibular occlusal plane, which contained the distobuccal cusps of the last molars and the origin. The x-axis passed through the origin and was perpendicular to the line of the distobuccal cusps of the last molars, with the positive x-axis pointing anteriorly. The y-axis passed through the origin and was parallel to the line of the distobuccal cusps of the last molars, with the positive external axis pointing to the left. The z-axis passed through the origin and is perpendicular to the x–y plane, with the positive z-axis pointing upwards (Fig. 4a-b).

Fig. 4
figure 4

The process of constructing a 3D occlusal force analysis model. a-b. Construct the coordinate system. c. Construct a fitted plane. d. Set the occlusal force direction. e. Construct a occlusal force indicator segment. f. Fitting planes to the occlusal points of the entire dentition. g-h. 3D occlusal force analysis model of the entire dentition

Full size image

Following, we presented an example of occlusal force model construction using the occlusal contact point (A1) on the mandibular second molar. First, the plane fitting function was used to obtain the fitted plane for each occlusal contact point (Fig. 4c). The opposite direction of the normal of the fitted plane was the direction of the occlusal force on this occlusal contact point (Fig. 4d). Using the center of the fitting plane as the base point and the absolute value of the bite force as the length, a line segment was constructed along the direction of the bite force (Fig. 4e). The coordinate values of the two end points of this line segment were noted as (x1, y1, z1) and (x2, y2, z2). The diff. of the x-coordinates of the two endpoints (x1-x2) was the magnitude of the component force in the x-axis direction of the bite force on this occlusal contact point. Similarly, the diff. of the y-coordinate (y1-y2) and the z-coordinate (z1-z2) of the two endpoints was the magnitude of the component forces of the occlusal force on the y and z axes.

By adding up the values of the occlusal component forces in the x-axis direction for all occlusal contact points on the second molar, the value of the component forces in the x-axis direction to which the second molar was subjected can be obtained. The component forces on the second molar in the y-axis and z-axis can also be calculated in the same way. The forces on the other teeth can be analysed in the same way to create a 3D occlusal force analysis model of the entire mandibular dentition (Fig. 4f-h).

Clinical application of the 3D occlusal force analysis system

The clinical demonstration was carried out on a patient (30 years old) with bruxism. She had complete dentition; no periodontal disease; and no orthodontic treatment. Ethical approval was granted by the Ethical Committee of the first author’s university (approval number: IRB-REV-2021143). She gave informed consent before participating in the study.

Results

Evaluation of the reliability of SA and DP

The OCA, OCN and the corresponding ICC values of two methods are summarized in Table 1. The ICC values for OCA and OCN measured by both the SA and DP systems were higher than 0.9, so it can be confirmed that both analysis systems have a high reliability.

Table 1 Mean OCA values, OCN values and the intraclass correlation coefficient (ICC) of SA and DP
Full size table

Evaluation of the validity of SA and DP

The results of the paired t-test showed a significant difference between the OCA obtained from the two systems (t = 3.017, P < 0.01) (Fig. 5), while there was no significant difference between the OCN obtained from the two methods (t = 0.691, P > 0.05) (Fig. 6a).

Fig. 5
figure 5

Results of the paired t-test between the OCA obtained from DP and SA

Full size image
Fig. 6
figure 6

Paired t-test and Bland–Altman plot for the OCN. a. Results of the paired t-test between the OCN obtained from DP and SA. b. Bland–Altman plot illustrating the agreement between the OCN obtained from DP and SA

Full size image

For data with no statistically significant differences in the paired t-tests, the Bland–Altman analysis showed that all data except one fell within the 95% limit of agreement of the two methods, which indicated that DP is consistent with SA in measuring OCN (Fig. 6b). Pearson correlation analysis showed a significant correlation between the OCA obtained from DP and SA analysis (R = 0.68, p < 0.001).

Based on these results, it can be seen that there is good consistency between DP and SA methods, therefore it is feasible to combine them to construct a 3D occlusal force analysis system.

Occlusal forces by 3D occlusal force analysis

Analysis of the occlusal forces in this patient showed that the occlusal forces changed in response to tooth position. The occlusal force in the anterior region < premolar region < molar region, both in terms of the resultant force and in terms of the x-, y- or z-axis components (Fig. 7). In addition, the forces on the individual teeth are clearly illustrated above. The vertical forces point in the negative direction of the z-axis, while the x- and y-axis components point in different directions.

Fig. 7
figure 7

The resultant force and the component forces on the x-, y- and z-axes of the occlusal force in each tooth position

Full size image

Discussion

Occlusal contact analysis, including the location of contact, OCA, OCN and occlusal force of each tooth, is essential in dentistry, especially in prosthetics and orthodontics, as maintaining the balance of occlusal contact and force of the teeth or prosthesis is the goal of the occlusal adjustment. However, there is still a lack of a convenient and reliable method which can achieve the abovementioned occlusal contact information simultaneously. In this study, after verifying the consistency between the 2D and 3D occlusion analysis systems, we have developed a novel occlusion analysis method to locate occlusal contact and quantitatively analyze OCA, OCN and occlusal forces of each tooth.

In evaluation trial, the reliability and validity of two analysis techniques were evaluated. The results indicated that the ICC values obtained from two systems were higher than 0.9, which indicated high stability for both two systems. Paired t-tests demonstrated no significant difference in the OCN values obtained from the DP and SA analysis. The following Bland–Altman test showed good consistency between the results of the two systems. Therefore, it can be considered that these two methods have a high consistency in measuring the OCN. In measuring OCA, although paired t-test showed that a significant difference between the data obtained from these two analysis systems, a significant correlation was indicated by Pearson correlation analysis. The result that the OCNs were the same while the OCAs were proportionally enlarged may be due to the influence of the media used in the analysis systems. The pressure sensitive film of DP comprises three layers of PET, which is more resistant to compression deformation than articulating papers. In addition, the dye of the articulating paper has spreading ability in the presence of saliva [30, 31]. Thus, the stained area of articulating paper might extend beyond the actual occlusal contact area. From this point of view, the difference OCA values did not affect the distribution of the occlusal contact as similar OCN values were found. In clinical demonstration, analysis of the occlusal forces showed that the occlusal forces changed in response to the tooth position. Usually, the first molar is subjected to the greatest force. However, for this patient with bruxism, the second molar is subjected to the greatest occlusal force during occlusion. This anomaly results in more wear of the cusps of the second molar. Furthermore, we can clearly see from the data how the teeth are subjected to forces in different directions. For example, the patient's second molar teeth on the left and right side have opposite directions of force in the y-axis, which cannot be identified in a two-dimensional force analysis. Many oral diseases are caused by imbalance in occlusal forces and it is easy to misdiagnose the two forces as the same based on the force values alone. The identification of the direction of force will be of great help in the treatment and diagnosis of diseases.

The difference between the 2D analysis results and the 3D dentition, caused by the loss of spatial information, will cause inconvenience in the clinical application of these occlusal analysis systems [32]. For example, quantitative analysis results (OCA or occlusal contact force) from T-scan and DP can not be used directly to locate the occlusal contact on the surface of teeth in clinical practice. In recent years, with the introduction of digital technology into dental practice, some 3D occlusal analysis systems were designed [33, 34]. For example, the occlusal contact analysis function that comes with the intraoral scanner, the transillumination technique used in the study by DeLong et al. [32] and the virtual occlusion analysis system proposed by Li et al. [35]. These methods achieved quantitative analysis of the OCA in three dimensions, however, they did not include the function of occlusal force analysis. After verifying the consistency between the two systems in detect occlusal contact, we constructed a 3D occlusal analysis method system by combining the advantages of respective systems. This new method not only achieved a 3D spatial location of occlusal contact points, but also combined the force analysis function to make a powerful and quantitative evaluation of occlusal contact of nature teeth or prosthesis. These innovations provide clinicians with more realistic and comprehensive information on occlusal contact, which would improve the accuracy of clinical diagnosis and treatment, as well as improve their clinical decision-making ability.

Another potential advantage of this novel occlusal analysis method is that it is more accurate and flexible in occlusal force analysis. It can not only decompose the bite force, but also specify the direction of force division as required. These characteristics have not been reported in previous studies. Prado et al. [36] applied T-scan to three-dimensional dentition analysis with the help of oral appliances. However, oral appliances increase the inconvenience of occlusion collection. In addition, due to the limitations of the T-scan [37], it can only display the relative value of the force and cannot obtain the absolute magnitude of the occlusal force, let alone the decomposition of the occlusal force. The study by Hattori et al. proposed a method to set the occlusal force value and direction and initially constructed a 3D occlusal force analysis system. However, its arithmetic is quite complicated and cannot be flexibly adjusted to clinical needs [38]. In our study, the constructed method could allow analytical calculations of the magnitude of the occlusal forces in the proximal-distal or buccolingual directions or any other direction required, as well as the magnitude of the fractional forces on individual tooth or combinations of several teeth in different directions, as required. It is worth noting that the calculation of the magnitude of forces in directions specific direction, such as proximal, distal, buccolingual and others, is of great importance in clinical practice, especially in prosthetic treatment, because abnormal forces can lead to occlusal instability and damage.

In addition, as the pressure-sensitive film and intraoral scanning techniques used in this method are simple to operate, this new occlusal analysis method has the potential advantages of simple operation and intuitive analysis results. Occlusal contact analysis methods in previous studies are unable to visualize the direction and magnitude of the occlusal forces. In the constructed method in this study, the length of the line segment to simulate the magnitude of the occlusal force and the direction of the line segment to illustrate the direction of the occlusal force. This allows for a more visual presentation of the results of the occlusal analysis and facilitates clinical work, for example, in presenting and explaining the abnormal occlusal conditions to patients.

Although the new method system has several potential advantages mentioned above, there are also some limitations that need to be further studied. At this stage, this 3D occlusal force analysis method needs to be constructed manually and the simulation of occlusal forces at each occlusal contact point repeats the same operational steps. In future research, we will try to apply artificial intelligence and other methods to realize the automation of these operations, and further improve the efficiency and automation level of the new method. Besides, the inability to obtain dynamic occlusal force changes throughout mandibular movements is also the limitation of the system. To address this issue, more computer-aided simulation and occlusal analysis tools are needed.

Conclusion

In summary, this study constructed a novel occlusion analysis method which can not only locate the occlusal contact in teeth or prosthesis, but also quantitatively analyze the OCA, OCN and occlusal forces simultaneously. The magnitude and direction of occlusal force of each contact point can be intuitively displayed on the 3D model with line segments. This new method would help to promote the accuracy of clinical diagnosis and treatment, especially in the field of prosthodontics, implants, and orthodontics.

Availability of data and materials

Data that support the findings of this study are available from the corresponding author [F.W.], upon reasonable request.

Abbreviations

SA:

Scanning of articulating paper marks

DP:

Dental Prescale analysis system

ICC:

Intraclass correlation coefficient

ICP:

Intercuspal position

OCA:

Occlusal contact area

OCN:

Occlusal contact number

PET:

Polyethylene terephthalate

References

  1. Kordaß B, Amlang A, Hugger A, Behrendt C, Ruge S. Number and localization of occlusal contact areas on natural posterior teeth without dental findings - evaluations of the regional baseline study (SHIP-1) with the Greifswald Digital Analyzing System (GEDAS). Int J Comput Dent. 2022;25:47–56.

    PubMed  Google Scholar 

  2. Lee HS, Ko KH, Huh YH, Cho LR, Park CJ. Correlation between occlusal contact area at various levels of interocclusal thicknesses and masticatory performance. J Oral Rehab. 2022;49:522–8. https://doi.org/10.1111/joor.13292.

    Article  Google Scholar 

  3. Idris RI, Shoji Y, Lim TW, MClinDent, MPros. Occlusal force and occlusal contact reestablishment with resin-bonded fixed partial dental prostheses using the Dahl concept: A clinical study. J Prosthet Dent. 2022;127:737–43. https://doi.org/10.1016/j.prosdent.2020.11.035.

  4. Wada M, Mameno T, Tsujioka Y, Yamashita M, Ikebe K. Effective utilization of digital technology in complete denture fabrication. J Oral Sci. 2022;64:172–4. https://doi.org/10.2334/josnusd.21-0381.

    Article  PubMed  Google Scholar 

  5. Pinheiro FHSL, Frota CM, Garib DG, Sathler R, Ozawa TO, Lauris RCMC, Kato RM, Kurimori ÉT. A cleft-customized occlusal rating system to assess orthodontic occlusal improvement in patients with unilateral cleft lip and palate. Cleft Palate Craniofac J. 2022;59:54–65. https://doi.org/10.1177/1055665621995313.

  6. Cong A, Massaro C, Ruellas ACO, Barkley M, Yatabe M, Bianchi J, Ioshida M, Alvarez MA, Aristizabal JF, Rey D, et al. Dental long axes using digital dental models compared to cone-beam computed tomography. Orthod Craniofac Res. 2022;25:64–72. https://doi.org/10.1111/ocr.12489.

    Article  PubMed  Google Scholar 

  7. Wiechens B, Quast A, Klenke D, Brockmeyer P, Schliephake H, Meyer-Marcotty P. Evaluation of occlusal function during orthognathic therapy : A prospective clinical trial using a digital registration method. J Orofac Orthop. 2022. https://doi.org/10.1007/s00056-022-00382-x.

  8. Raj R, Koli DK, Bhalla AS, Jain V, Manchanda S, Nanda A. Effect of rehabilitation by using the shortened dental arch concept on the thickness of the masseter muscle and occlusal force: A pilot study. J Prosthet Dent. 2022. https://doi.org/10.1016/j.prosdent.2021.12.009.

    Article  PubMed  Google Scholar 

  9. Kang YF, Ding MK, Qiu SY, Cai ZG, Zhang L, Shan XF. Mandibular reconstruction using iliac flap based on occlusion-driven workflow transferred by digital surgical guides. J Oral Maxillofac Surg. 2022;80:1858–65. https://doi.org/10.1016/j.joms.2022.07.140.

  10. Majithia IP, Arora V, Anil Kumar S, Saxena V, Mittal M. Comparison of articulating paper markings and t scan iii recordings to evaluate occlusal force in normal and rehabilitated maxillofacial trauma patients. Med J Armed Forces India. 2015;71:S382–S388. https://doi.org/10.1016/j.mjafi.2014.09.014.

  11. Stoica ET, Marcauteanu C, Tudor A, Duma V-F, Amaricai EC, Onofrei R, Suciu O, Negrutiu ML, Sinescu C. Influence of the text neck posture on the static dental occlusion. Medicina (Kaunas). 2022;58:1303. https://doi.org/10.3390/medicina58091303.

    Article  PubMed  Google Scholar 

  12. Hiroshi S, Marie K, Hanako U, Mako S, Masaoki Y, Kunihisa N, Ayano I. Comparison of two dental prescale systems used for the measurement of occlusal force. Odontology. 2020;108:676–80. https://doi.org/10.1007/s10266-020-00509-9.

    Article  Google Scholar 

  13. Okada Y, Sato Y, Kitagawa N, Uchida K, Osawa T, Imamura Y, Terazawa M. Occlusal status of implant superstructures at mandibular first molar immediately after setting. Int J Implant Dent. 2015;1:16. https://doi.org/10.1186/s40729-015-0016-0.

  14. Wang TM, Chang YH, Yang TC, Lin LD. Effect of scan delay on measurements of an occlusal pressure sensitive film: An in-vitro study. J Dental Sci. 2022;17:30–4. https://doi.org/10.1016/j.jds.2021.08.005.

    Article  Google Scholar 

  15. Iwasaki M, Maeda I, Kokubo Y, Tanaka Y, Ueno T, Ohara Y, Motokawa K, Hayakawa M, Shirobe M, Edahiro A, et al. Standard values and concurrent validity of a newly developed occlusal force-measuring device among community-dwelling older adults: the otassha study. Int J Environ Res Public Health. 2022;19:5588. https://doi.org/10.3390/ijerph19095588.

    Article  PubMed  PubMed Central  Google Scholar 

  16. Shiga H, Komino M, Yokoyama M, Sano M, Arakawa I, Nakajima K, Fujii S. Relationship between age and occlusal force in adults with natural dentition. Odontology. 2023;111:487–92. https://doi.org/10.1007/s10266-022-00750-4.

  17. Kwon H, Park SH, Jung HI, Hwang WC, Choi YJ, Chung C, Kim KH. Comparison of the bite force and occlusal contact area of the deviated and non-deviated sides after intraoral vertical ramus osteotomy in skeletal Class III patients with mandibular asymmetry: Two-year follow-up. Korean J Orthod. 2022;52:172–81. https://doi.org/10.4041/kjod21.236.

  18. Lahoud P, Jacobs R, Boisse P, EzEldeen M, Ducret M, Richert R. Precision medicine using patient-specific modelling: state of the art and perspectives in dental practice. Clin Oral Investig. 2022;26:5117–28. https://doi.org/10.1007/s00784-022-04572-0.

  19. Tian S, Huang R, Li Z, Fiorenza L, Dai N, Sun Y, Ma H. A dual discriminator adversarial learning approach for dental occlusal surface reconstruction. J Healthcare Eng. 2022;2022:1933617. https://doi.org/10.1155/2022/1933617.

    Article  Google Scholar 

  20. Woodsend B, Koufoudaki E, Ping Lin GM, El-Angbawi A, Aziz A, Shaw W, Semb G, Reesu GV, Mossey PA. Development of intra-oral automated landmark recognition (ALR) for dental and occlusal outcome measurements. Eur J Orthod. 2022;44:43–50. https://doi.org/10.1093/ejo/cjab012.

    Article  PubMed  Google Scholar 

  21. Giese-Kraft K, Jung K, Schlueter N, Vach K, Ganss C. Detecting and monitoring dental plaque levels with digital 2D and 3D imaging techniques. PLoS ONE. 2022;17:1–14. https://doi.org/10.1371/journal.pone.0263722.

    Article  Google Scholar 

  22. Moore BK, Deane S, Huang W, Kim J, Parthasarathi K. Occlusal comparison of hand-articulation versus digital articulation in orthognathic surgery. Br J Oral Maxillofac Surg. 2022;60:443–7. https://doi.org/10.1016/j.bjoms.2021.07.013.

    Article  PubMed  Google Scholar 

  23. Michou S, Vannahme C, Bakhshandeh A, Ekstrand KR, Benetti AR. Intraoral scanner featuring transillumination for proximal caries detection An in vitro validation study on permanent posterior teeth. J Dentist. 2022;116:103841. https://doi.org/10.1016/j.jdent.2021.103841.

    Article  Google Scholar 

  24. Sigvardsson J, Nilsson S, Ransjö M, Westerlund A. Digital quantification of occlusal contacts: a methodological study. Int J Environ Res Public Health. 2021;18:5297. https://doi.org/10.3390/ijerph18105297.

    Article  PubMed  PubMed Central  Google Scholar 

  25. Rajshekar M, Julian RD, Williams AMM, Tennant ML, Forrest AS, Walsh LJ, Wilson GJ, Blizzard L. The reliability and validity of measurements of human dental casts made by an intra-oral 3D scanner, with conventional hand-held digital callipers as the comparison measure. Forensic Sci Int. 2017;278:198–204. https://doi.org/10.1016/j.forsciint.2017.07.009.

    Article  PubMed  Google Scholar 

  26. Michelinakis G, Apostolakis D, Tsagarakis A, Kourakis G, Pavlakis E. A comparison of accuracy of 3 intraoral scanners: A single-blinded in vitro study. J Prosthet Dent. 2020;124:581–8. https://doi.org/10.1016/j.prosdent.2019.10.023.

  27. Conejo J, Han S, Atria PJ, Stone-Hirsh L, Dubin J, Blatz MB. Full digital workflow to resolve angled adjacent dental implants: A dental technique. J Prosthet Dent. 2022. https://doi.org/10.1016/j.prosdent.2022.07.012.

    Article  PubMed  Google Scholar 

  28. Marques S, Ribeiro P, Gama C, Herrero-Climent M. Digital guided veneer preparation: A dental technique. J Prosthet Dent. 2022. https://doi.org/10.1016/j.prosdent.2022.04.035.

    Article  PubMed  Google Scholar 

  29. Ayuso-Montero R, Mariano-Hernandez Y, Khoury-Ribas L, Rovira-Lastra B, Willaert E, Martinez-Gomis J. Reliability and validity of T-scan and 3d intraoral scanning for measuring the occlusal contact area. J Prosthodont. 2020;29:19–25. https://doi.org/10.1111/jopr.13096.

    Article  PubMed  Google Scholar 

  30. Tammataratarn P, Chen MC, Lin CH, Ko EWC. Sequential digital occlusal analysis in patients with skeletal Class III malocclusion with orthognathic surgery: Surgery-first vs orthodontic-first approach. Am J Orthod Dentofac Orthop. 2022;162:927–36. https://doi.org/10.1016/j.ajodo.2021.07.030.

  31. Jeong MY, Lim YJ, Kim MJ, Kwon HB. Comparison of two computerized occlusal analysis systems for indicating occlusal contacts. J Adv Prosthod. 2020;12:49–54. https://doi.org/10.4047/jap.2020.12.2.49.

    Article  Google Scholar 

  32. DeLong R, Knorr S, Anderson GC, Hodges J, Pintado MR. Accuracy of contacts calculated from 3D images of occlusal surfaces. J Dent. 2007;35:528–34. https://doi.org/10.1016/j.jdent.2007.02.004.

  33. Hennen MV, Blum H, Dammaschke T. Accuracy and reproducibility of the visualization of occlusal contact points using analog articulating foil or digital intraoral scanners in vitro. Int J Comput Dent. 2022;25:173–80.

  34. Bostancıoğlu SE, Toğay A, Tamam E. Comparison of two different digital occlusal analysis methods. Clin Oral Invest. 2022;26:2095–109. https://doi.org/10.1007/s00784-021-04191-1.

  35. Li L, Chen H, Wang Y, Sun Y. Construction of virtual intercuspal occlusion: considering tooth displacement. J Oral Rehabil. 2021;48:701–10. https://doi.org/10.1111/joor.13153.

  36. Prado Id, Iturrate M, Minguez R, Solaberrieta E. Evaluation of the accuracy of a system to align occlusal dynamic data on 3D digital casts. BioMed Res Int. 2018;2018:8079089. https://doi.org/10.1155/2018/8079089.

    Article  PubMed  PubMed Central  Google Scholar 

  37. Huang YF, Wang CM, Shieh WY, Liao YF, Hong HH, Chang CT. The correlation between two occlusal analyzers for the measurement of bite force. BMC Oral Health. 2022;22:472. https://doi.org/10.1186/s12903-022-02484-9.

    Article  PubMed  PubMed Central  Google Scholar 

  38. Hattori Y, Satoh C, Kunieda T, Endoh R, Hisamatsu H, Watanabe M. Bite forces and their resultants during forceful intercuspal clenching in humans. J Biomech. 2009;42(10):1533–8. https://doi.org/10.1016/j.jbiomech.2009.03.040.

Download references

Acknowledgements

This study was supported by grants from the National Clinical Research Centre for Oral Diseases (Grant No. LCB202005).

Funding

This research received no external funding.

Author information

Author notes

  1. Zhe Zhao and Qing Wang are co-first authors.

Authors and Affiliations

  1. State Key Laboratory of Military Stomatology & National Clinical Research Center for Oral Diseases, Department of Prosthodontics, School of Stomatology, The Fourth Military Medical University, Xi’an, Shaanxi, 710032, PR China

    Zhe Zhao, Qing Wang, Jiale Li, Ming Zhou, Kai Tang, Jihua Chen & Fu Wang

Authors
  1. Zhe Zhao
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Qing Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jiale Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Ming Zhou
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Kai Tang
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Jihua Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Fu Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Z.Z. did the measurements, prepared the original draft and wrote the manuscript. Q.W. collected data and did the statistical analysis. J.L.L., K.T. and M.Z. prepared Figs. 1, 2, 3, 4, 5, 6 and 7 and substantively revised manuscript. J.H.C. and F.W. contributed to the study conception and design and helped modify the manuscript. All authors have read and agreed to the published version of the manuscript.

Corresponding authors

Correspondence to Jihua Chen or Fu Wang.

Ethics declarations

Ethics approval and consent to participate

The study was conducted according to the guidelines of the Declaration of Helsinki, and approved by the Ethical Committee of Stomatological Hospital of the Fourth Military Medical University (approval no. IRB-REV-2021143). Informed consent was obtained from all subjects involved in the study.

Consent for publication

Not applicable.

Competing interests

The authors declare no conflict of interest.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhao, Z., Wang, Q., Li, J. et al. Construction of a novel digital method for quantitative analysis of occlusal contact and force. BMC Oral Health 23, 190 (2023). https://doi.org/10.1186/s12903-023-02899-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1186/s12903-023-02899-y

Keywords

BMC Oral Health

ISSN: 1472-6831

Contact us